top-menu menu
kep series
     
spacer
Model KEP 4500 KEP 9000 KEP 10000
Power Stereo Mode
2 0hms / 1KHz / 1% THD RMS 1250W x 2 1900W x 2 2400W x 2
4 0hms / 1KHz / 1% THD RMS 800W x 2 1300W x 2 2000W x 2
8 0hms / 1KHz / 1% THD RMS 500W x 2 800W x 2 1200W x 2
Power Bridge Mono Mode
4 0hms / 1KHz / 1% THD RMS 2200W 3000W RMS 4800W RMS
8 0hms / 1KHz / 1% THD RMS 1700W 2100W RMS 4000W RMS
Single to Noise Ratio
A-weighted
>100dB
Residual Noise, A-weighted <-60dBu
Input Sensitivity 32dB / 26dB / 0,775V
Total Harmonic Distortion <0,02%
Frequency Response ± 1dB 1W RMS 10Hz-40kHz 8 ohms / ±0.2dB @ 8 ohms 20Hz - 20kHz 8 ohms
Input Impedance 10k ohms unbalanced, 20k ohms balance
Damping Factor, 1 kHz <300 at 8 ohms
Slew Rate 40V/uS
Power Requirements 100V, 120V, 220V, 230V, 240V, 50/60Hz (factory configured)
Protections Over-heat , short-circuit, DC, over-current, mismatched loads
Cooling System Dual Speed Fans and Heats sinks
Max. Power Consumption
output power @ 4 ohms
1800W - -
Max. Power Consumption
output power @ 8 ohms
- 9A @ 230V 11A @ 230V
Net weigth 15.9 Kg (31Lb) 28Kg (61.6Lb) 33Kg (72.8Lb)
Dimensions (H x W x H) 3.5" x 19" x 15,9"
(8.8cmm x 48.3cm x 40.7cm)
5.25" x 19" x 15,9"
(13.3cm x 48.3cm x 40.7cm)
5.25" x 19" x 18.3"
(13.3cm x 48.3cm x 46.2cm)
spacer
     
  Download KEP 4500 English - Spanish User`s Manual  
     
  Download KEP 9000 / 10000 English - Spanish User`s Manual  
     
     
 
Model KDA10K
General
Number of channels  4
Peak total output both channels driven  8800 W
Peak output voltage per channel  141 V
Max. output current per channel  35.5 Arms
General
Max. Output Power 16 ohms 8 ohms 4 ohms 2 ohms 70 Vrms/100 Vrms peak
Per ch. (both ch.’s driven) 625 W 1250 W 2100 W 2200 W 2200 W
Bridged per ch.  2500 W 4200 W 4600 W Not recommended
Performance with Gain: 35 dB and VPL: 195 V
THD 20 Hz - 20 kHz for 1 W  <0.1%
THD at 1 kHz and 1 dB below clipping  <0.05%
Signal To Noise Ratio  >112 dBA
Channel separation (Crosstalk) at 1 kHz  >70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB  6.8 Hz - 34 kHz
Input impedance  20 kOhm
Input Common Mode Rejection, CMR  50 dB
Output impedance @ 100 Hz 30 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 141, 118, 100, 85, 71, 59, 50, 42 V
VPL, selectable when bridged  282, 236, 200, 170, 142, 118, 100, 84 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 23, 26, 29, 32, 35, 38, 41, 44 dB
– rear-panel switches
Default gain  35 dB
Level adjustment (per ch.) Front-panel potentiometers
Connectors and Switches
Input connectors (per ch.)  XLR-3 electronically balanced
Output connectors (per ch.)  SPEAKON
Output bridge mode  A+B and/or C+D, inputs A and C are input source
Intelligent fans (on/off) depending on presence of output signal
Power on/off  switch on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators:
Common  Power Average Limiter (PAL) ; Power on
Signal present ; -10 dB and -4 dB output signal; Voltage Peak Limiter (VPL); Current Peak Limiter (CPL);
Per channel Very High Frequency (VHF); High Temperature; Fault; Mute; Bridge
Power
Operating voltage, 220 V / 110 V nominal 170 -245 / 85-135 
Minimum power-up voltage, 220 V / 110 V 171 V / 85 V
Power Average Limiter (PAL)  Yes
Soft start / Inrush Current Draw Yes / max. 5A
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”)
Weight 12 kg (26.4 lbs.)
 
     
  Download KDA10K English User`s Manual  
 

 

spacer

k-logo


Product Line:
Line Array
Amplifiers
Mixers
Guitar & Bass Amplifiers
Active & Passive Speakers
PA Packs
Microphones
Accessories
Legacy Bestsellers



Download the
full line catalog here!

Contact:
info@kohlt-usa.com

Kohlt en español

Complete and send your Warranty from here